F-14_Park_Jet_Parts_Templates_75_Non-tiled.pdf

(69 KB) Pobierz
Canopy
Make 10 and laminate
with 3M 77 spray
Turtledeck sides
Make 2
Fwd fuselage doubler
Make 2
Strake middle piece
Make 2
Copyright © 2005
Designed by Steve Shumate
All Rights Reserved
Nose cone top
view template
(use to aid in
carving to shape)
doubler here
stall fwd fuse
In
ke 2
py sill - Ma
Cano
Cut top and bottom edges at a roughly 15 degree bevel
All parts are made from 6 mm Depron or
BlueCore foam unless otherwise specified
If you enjoy these plans, please consider sending a small contribution
to the designer to show your appreciation for all the work that went
into developing them. Suggested contribution is $10 U.S., and can
be sent via PayPal to jetset44@verizon.net. Thanks for your support!
Nose cone
Make 12 and laminate
with 3M 77 spray
F-1
F-2
Forward fuselage sides
Make 2
strip here
F-3
Turtledeck top
(trim to fit)
Make 2
Install 2 layers of 3/8" foam
Fwd fuse top
Make 1
Fwd fuse top
doubler
Make 1
F-1
Make 1
F-2
Make 1
F-3
Make 1
4
Strake/inlet top
Make 1
Wing Strake Fences
Make 4 from 3mm Depron
Cut hole to access
wing swing servo
Aft wing cover
Make 1
Cut access hatch for receiver
and rudder servo
2
Fwd Fuselage Gun Pod
(sand to shape)
Make 1
Center support for aft wing cover
Make 2 and laminate
Scale in inches
0
2
4
Upper wing air exhausts
(decoration)
Make 2
Rudder servo tray
Make 3 and laminate
Inlet diverter
Make 2
Fwd strake bottom piece
Make 2
Wing panel
Make 2
Center aft fuselage
top piece
Make 1
Taileron servo doubler
Make 2
Vertical tail brace - Make 2
Cut slot at 5 deg angle
Motor mount
Middle piece
Make 2
Motor mount
Top piece
Make 2
Aft wing cover
center piece
Make 1
Aft strake bottom piece
Make 2
Cut slot at 5 deg angle
for vertical tails
Aft inlet tops
Make 2
Stabilator
Make 2
Drill 1/4" holes both sides
(after assembled)
Install 3/8" foam strips here
Motor mount
Bottom piece
Make 1
Cut slots to accept tabs
on center fuselage bottom
Inlet inboard sides
Make 2
Cut hole to fit
servo used
.75" x .75" 1/64" ply
doublers on inboard side
(drill 3/16" hole for pivot
bearing tubes)
Cut slot to fit
motor mount
Install 3/8" foam strips here
Wing sweep servo tray
Make 1 from 1/8" lite-ply
Wing sweep servo
tray spacer
(make 1 from 3/8" balsa)
(1.0" x 1.87")
Install 3/8" foam strips here
Lite-ply doubler
underneath
Vertical tail
Make 2
Temporary
Inlet
Bulkhead 3
Make 1
Inlet outboard sides
Make 2
Wing sweep spar box shear webs
Make 2 from 1/4" hard balsa (0.5" height x 8.5" length)
Cut hole to fit servo
used (HS-81 shown)
Install balsa servo
tray spacer
on top here
Wing sweep spar box top and bottom
Make 2 from 1/8" lite-ply
Install 3/8" foam strips here
Wing sweep servo arm
Make 1 from 1/8" lite-ply
0.19"
0.58"
0.61"
Install root fairings here
(one on each side)
Right wing
Left wing
Adjust hole spacing on both sides
as required to get proper amount
of swing angle in each wing
(dimensions shown are what worked
with the HS-81 servo used on prototype).
Note these holes are not necessarily
symmetrical.
Vertical tail root fairing - Make 4
Wing swing arm spacer
(make 4 from 1/8" lite-ply,
laminate to make 2 pairs)
(0.5" x 1.0")
Rudder control horns
(make 2 from 1/32" plywood)
Temporary
Inlet
Bulkhead 1
Make 1
Temporary
Inlet
Bulkhead 2
Make 1
Inlet bottoms
Make 2
Drill 1/16" hole
Drill 1/4" hole thru
(after assembly)
Install spacer
spacer here
a rm
wing ply
ing s /8" lite-
1
er w
Upp 2 from
e
Mak
Wing sweep spar box
tongue doublers
Make 4 from 1/8" lite-ply
a rm
wing ply
ing s /8" lite-
1
er w
L o w 2 f ro m
e
Mak
Center fuselage bottom
Make 1

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin