PCI.TXT

(13 KB) Pobierz



              The PCI (Peripheral Component Interconnect) Bus

This file is not intended to be a thorough coverage of the PCI standard.
It is for informational purposes only, and is intended to give designers
and hobbyists an overview of the bus so that they might be able to design
their own PCI cards. Thus, I/O operations are explained in the most
detail, while memory operations, which will usually not be dealt with
by an I/O card, are only briefly explained. Hobbyists are also warned
that, due to the higher clock speeds involved, PCI cards are more
difficult to design than ISA cards or cards for other slower busses.
Many companies are now making PCI prototyping cards, and, for those
fortunate enough to have access to FPGA programmers, companies like
Xilinx are offering PCI compliant designs which you can use as a starting
point for your own projects.

For a copy of the full PCI standard, contact:

     PCI Special Interest Group (SIG)
     PO Box 14070
     Portland, OR 97214
     1-800-433-5177
     1-503-797-4207

     There is also a spec for CompactPCI, which uses the same timing
and signals, but uses a eurocard connector and format. This is not
presently covered in any detail within this document.


Pinout (5 volt and 3.3 volt boards)


               -12V     01      *TRST
                TCK             +12V
                GND             TMS
                TDO             TDI
                +5V             +5V
                +5V             *INTA
              *INTB             *INTC
              *INTD             +5V
            *PRSNT1             reserved
           reserved     10      +I/O V (+5 or +3.3)
            *PRSNT2             reserved
                GND   Key3.3    GND
                GND   Key3.3    GND
           reserved             reserved
                GND             *RST
                CLK             +I/O V (+5 or +3.3)
                GND             *GNT
                REQ             GND
+I/O V (+5 or +3.3)     20      reserved
               AD31             AD30
               AD29             +3.3V
                GND             AD28
               AD27             AD26
               AD25             GND
              +3.3V             AD24
              C/BE3             IDSEL
               AD23             +3.3V
                GND             AD22
               AD21             AD20
               AD19     30      GND
              +3.3V             AD18
               AD17             AD16
              C/BE2             +3.3V
                GND             *FRAME
              *IRDY             GND
              +3.3V             *TRDY
            *DEVSEL             GND
                GND             *STOP
              *LOCK             +3.3V
              *PERR     40      SDONE
              +3.3V             *SBO
              *SERR             GND
              +3.3V             PAR
              C/BE1             AD15
               AD14             +3.3V
                GND             AD13
               AD12             AD11
               AD10     49      AD9
                GND    Key5     GND
                GND    Key5     GND
                AD8     52      C/BE0
                AD7             +3.3V
              +3.3V             AD6
                AD5             AD4
                AD3             GND
                GND             AD2
+I/O V (+5 or +3.3)             +I/O V (+5 or +3.3)
             *ACK64     60      *REQ64
                +5V             +5V
                +5V     62      +5V

             (64 Bit Bus Extension Only)
           reserved     63      GND
                GND             C/BE7
              C/BE6             C/BE5
              C/BE4             +I/O V (+5 or +3.3)
                GND             PAR64
               AD63             AD62
               AD61             GND
+I/O V (+5 or +3.3)     70      AD60
               AD59             AD58
               AD57             GND
                GND             AD56
               AD55             AD54
               AD53             +I/O V (+5 or +3.3)
                GND             AD52
               AD51             AD50
               AD49             GND
+I/O V (+5 or +3.3)             AD48
               AD47     80      AD46
               AD45             GND
                GND             AD44
               AD43             AD42
               AD41             +I/O V (+5 or +3.3)
                GND             AD40
               AD39             AD38
               AD37             GND
+I/O V (+5 or +3.3)             AD36
               AD35             AD34
               AD33     90      GND
           reserved             reserved
           reserved             GND
                GND     94      reserved


* - Active Low


PCI slots are keyed so that a 3.3 volt card cannot be plugged into a 5
        volt slot, and a 5.5 volt card cannot be plugged into a 3 volt
        card. Dual voltage cards are possible.
Key3.3 - At this location, a key is present on 3.3 volt boards. On 5 volt
        boards, these pins are GND.
Key5 - At this location, a key is present on 5 volt boards. On 3.3 volt
        boards, these pins are GND.

Signal Descriptions:

AD(x): Address/Data Lines.
CLK: Clock. 33 MHz maximum.
C/BE(x): Command, Byte Enable.
FRAME: Used to indicate whether the cycle is an address phase or
     or a data phase.
DEVSEL: Device Select.
IDSEL: Initialization Device Select
INT(x): Interrupt
IRDY: Initiator Ready
LOCK: Used to manage resource locks on the PCI bus.
REQ: Request. Requests a PCI transfer.
GNT: Grant. indicates that permission to use PCI is granted.
PAR: Parity. Used for AD0-31 and C/BE0-3.
PERR: Parity Error.
RST: Reset.
SBO: Snoop Backoff.
SDONE: Snoop Done.
SERR: System Error. Indicates an address parity error for special cycles
        or a system error.
STOP: Asserted by Target. Requests the master to stop the current transfer
        cycle.
TCK: Test Clock
TDI: Test Data Input
TDO: Test Data Output
TMS: Test Mode Select
TRDY: Target Ready
TRST: Test Logic Reset


The PCI bus treats all transfers as a burst operation. Each cycle begins
with an address phase followed by one or more data phases. Data phases
may repeat indefinately, but are limited by a timer that defines the
maximum amount of time that the PCI device may control the bus. This
timer is set by the CPU as part of the configuration space. Each device
has its own timer (see the Latency Timer in the configuration space).

The same lines are used for address and data. The command lines are also
used for byte enable lines. This is done to reduce the overall number
of pins on the PCI connector.

The Command lines (C/BE3 to C/BE0) indicate the type of bus transfer during
the address phase.

C/BE    Command Type
0000    Interrupt Acknowledge
0001    Special Cycle
0010    I/O Read
0011    I/O Write
0100    reserved
0101    reserved
0110    Memory Read
0111    Memory Write
1000    reserved
1001    reserved
1010    Configuration Read
1011    Configuration Write
1100    Multiple Memory Read
1101    Dual Address Cycle
1110    Memory-Read Line
1111    Memory Write and Invalidate


The three basic types of transfers are I/O, Memory, and Configuration.


PCI timing diagrams:


            ___     ___     ___     ___     ___     ___
CLK     ___|   |___|   |___|   |___|   |___|   |___|   |___

        _______                                   _________
FRAME          |_________________________________|

                ______  _______  ______  ______  ______
AD      -------<______><_______><______><______><______>---
                Address  Data1    Data2   Data3   Data4

                ______  _______________________________
C/BE    -------<______><_______________________________>---
                Command   Byte Enable Signals

         ____________                                   ___
IRDY                 |_________________________________|

         _____________                                  ___
TRDY                  |________________________________|

         ______________                                 ___
DEVSEL                 |_______________________________|


PCI transfer cycle, 4 data phases, no wait states.
Data is transferred on the rising edge of CLK.


                         [1]              [2]        [3]
            ___     ___     ___     ___     ___     ___     ___     ___
CLK     ___|   |___|   |___|   |___|   |___|   |___|   |___|   |___|   |__

        _______                                                  _________
FRAME          |________________________________________________|

                                   A               B               C
                ______           ______________  ______  _____________
AD      -------<______>---------<______________><______><_____________>---
                Address           Data1           Data2   Data3

                ______  ______________________________________________
C/BE    -------<______><______________________________________________>---
                Command   Byte Enable Signals

                                                         Wait
         ____________                                    _____         ___
IRDY                 |__________________________________|     |_______|

                        Wait            Wait
         ______________________         ______                         ___
TRDY                           |_______|      |_______________________|

         ______________                                                ___
DEVSEL                 |______________________________________________|


PCI transfer cycle, with wait states.
Data is transferred on the rising edge of CLK at points labled A, B, and ...
Zgłoś jeśli naruszono regulamin